Home / Products / Home Automation / Mx2wire

Navigation


Product Portfolio
6.81 MB
Price-List
3.21 MB
Demo Clips
Mx2wire
from: € 298.00 * (net)
 Manual Price list
Ethernet & PoE Via Two-Wire Cable.

Using the new Mx2wire system from MOBOTIX, an Ethernet network with PoE can be established up to 500 meters using two-wire cables (e.g. telephone cable, bell wire). This means that, for example, an existing two-wire analog telephone cable can be used to connect a 10/100 MB Ethernet device (for instance, PC, WLAN, IP camera, IP telephone or IP door station). The data rate is up to 30 Mbps. For 500 m of coaxial cable, approx. 15 Mbps data is transferred. An (identical) Mx2wire device is required at both ends of the cable, and it automatically configures itself as either the sender or the receiver.

The two Mx2wire nodes are supplied via PoE from the network cable that feeds in. The connected devices are supplied with up to 7 watts via PoE, since in addition to the network signal, also the PoE signal that is fed in is transferred. Mx2wire is supplied in the standard socket frame in different designs, however, it can also be used with the surface-mounted socket provided.

Scheme Mx2wire

Adapter set to transfer via Ethernet and PoE using a two-wire cable

  • Two-wire cables are used to connect 10/100 MB Ethernet devices
  • Ideal to connect e.g. a PC, WLAN, IP camera, IP telephone, IP door station
  • Data transfer distance up to 500 meters; data rate is up to 30 Mbps, depending on distance
  • Connected devices are supplied with up to 7 watts via PoE
  • Simple installation in standard socket frames or surface-mounted sockets
  • Developed and manufactured by MOBOTIX in Germany

NOTE: We have tested the product very carefully and, instead of specifying non-recurrent peak values, we only provide the important net data rate, which was measured over a long period of time. However, we can provide NO GUARANTEE of possible cable lengths, data rates and power transmission, as various physical factors are not within the area of responsibility of MOBOTIX (sources of interference such as machines or power cables, the condition and quality of the cables used, etc.). The nominal data rate, connection length and power transmission can only be individually tested and determined at the place of installation.

* 2008/04 • MSRP (Manufacturer's suggested retail prices) • Prices ex works Langmeil, Germany (EXW) • Excluding VAT and any other handling charges • Calculated at FXR EUR = 0.90484 GBP, 01/14/2009 • Information subject to change without notice!

 
   
  Mx2wire

 

 

Coxial cable
0.6 mm inner conductor

 

with 50 m
Data: 30 Mbps, PoE class: 2
with 100 m
Data: 30 Mbps, PoE class: 1
with 500 m
Data: 30 Mbps, PoE class: -

 

Telephone line/bell wire
0.8 mm

 

with 50 m
Data: 30 Mbps, PoE class: 2
with 100 m
Data: 30 Mbps, PoE class: 2
with 200 m
Data: 30 Mbps, PoE class: 1

 

Installation cable
1.5 sqmm

 

with 50 m
Data: 30 Mbps, PoE class: 2
with 100 m
Data: 30 Mbps, PoE class: 2
with 200 m
Data: 25 Mbps, PoE class: 2

 

Network cable**
Cat-7

 

with 200 m
Data: 30 Mbps, PoE class: 2
with 300 m
Data: 30 Mbps, PoE class: 2
with 500 m
Data: 30 Mbps, PoE class: 2

 

 

 

 

Article No.:

MX-2Wire-Set-PW

 

Price (net):
available
from: € 298.00 * (net)

** Mx2wire can also be used to extend the range of an Ethernet connection that would otherwise be limited to just 100 m in length (between the PoE switch and end device). For this purpose, a Cat7 installation cable is converted to a two-wire cable as follows: Open the four twisted wire pairs and remove approx. 7 mm of insulation from the ends. Then connect the four white wires together to one cable and the four colored wires together to another cable and attach wire-end sleeves. In conjunction with Mx2wire, PoE class 2 power can be transmitted over a distance of 500 m at a data rate of approx. 30 Mbps.