Release Notes for MOBOTIX Camera Software

Document Information

Contents

These Release Notes contain a technical description of the most important changes in the software for the MOBOTIX network camera line M7.

Software Releases—Overview

Notes:

• Please download the stable customer releases of the software from www.mobotix.com in the Services  > Download Center > Software Downloads section.
• Please note that some of the described features in the dialogs will only be visible if the More button at the bottom of a dialog has been pressed.
• Please send an email to support@mobotix.com for feedback.

top

Software Release MX-V7.3.2.76 − for M7 Camera Models M73, S74, Q71, D71, c71, p71, p71TA, v71

Creation Date: 2023-04-26

Publishing Date: 2023-05-02

Enhancements and improvements

Integration of MQTT protocol

This version supports the widely used, efficient and bandwidth-optimized MQTT network protocol for exchanging messages between IoT devices. The camera can use the so-called MQTT broker to publish its own messages, for example when certain events occur, as well as subscribe to messages from other MQTT devices and react accordingly when they are received. For this purpose, the following new dialogs and functions have been implemented:

• The new Admin Menu > Network Configuration > MQTT Configuration dialog is used to activate MQTT, configure the MQTT broker, and define the data and events to be published as MQTT messages.
• In the Setup Menu > Event Control > Event Overview dialog, the new event sensor type MQTT Subscription for receiving MQTT network messages can be selected and configured when adding message events.

For more information, see the program's online help

Improvements in the area of integration protocols, ONVIF and RTP streaming

RTP-RAW-Streaming

• Support for additional mono camera models
  Raw streaming mode is now also supported for the following camera models:
• Camera models with only one image sensor - Q71, D71, c71, p71, P71TA and v71
• Dual-sensor cameras with only one connected sensor
• Optical (non-thermal) image sensors on thermal camera
• 2 x 4K RTP RAW streaming
  Previously, only one of two 4K RTP video streams could be enabled on the Integration Protocols settings page (Admin menu > Camera Administration > Integration Protocols). This restriction has now been lifted so that customers are now able to retrieve RTP video streams from all available video encoders at the same time.
• Increased flexibility in RTP RAW streaming/mode
  The image source ("Full" or "Raw" streaming mode) of RTP video streams can now be configured individually for each video stream on the Integration Protocols configuration page (Admin menu > Camera Administration > Integration Protocols). In previous versions of the camera software, the image source could only be configured globally for all RTP video streams at the same time.

Integration Mode, ONVIF Fail-Over, and Genetec Settings

• Configuration of RTP Video Encoder Parameters
  The Admin Menu > Camera Administration > Integration Protocols dialog now supports the configuration of video encoder parameters in the ONVIF, Genetec, and Genetec+ONVIF integration modes. In previous releases, the RTP video stream parameters could only be changed in compatible VMS clients.
• Audio streaming support for ONVIF failover recording
  The camera now also supports streaming recorded audio from ONVIF (failover) recordings to VMS systems. In previous versions of the camera's software, audio was recorded to the camera's SD card, but not streamed through the camera's RTP server.
• Support for Genetec audio alarm events
  Audio alarm events are now supported for Mx7 series cameras through the camera's Genetec integration API.

Other improvement

• Microphone Event
  An existing microphone can now be used to define a microphone event in the Environment Events section of the Setup menu > Event Control > Event Overview dialog. This applies to the integrated microphone in the audio and MultiSense module as well as to a connected microphone, the line-in connection of the S74 audio IO plug-in card and the microphone of the mono models Q71, D71, c71, p71 and v71.
• New lenses (8° and F1.0)
  This version supports image sensor modules with the new super-telephoto lens (8° angle of opening) and the new very light-sensitive lens, which has an F1.0 aperture.
• OpenVPN client with SHA256
  In  the Admin Menu > Network Setup> OpenVPN Client Settings dialog, the value SHA256 can now also be selected for the Authentication option.
• Variables for digital input/output
  With the new variables $(SEN.IN1),$(SEN.OU1 and $(SEN.OU2), the current status (value 0 or 1) of any digital inputs and outputs of a MOBOTIX 7 camera can be determined. As usual, the variables can be used, for example, to display the values in the live image or to transmit the values within a network message.
  ATTENTION: These variables replace the variables $(SEN.INA) to $(SEN.INP)!
• Variables for IR and white light illumination
  The following new variables can be used to determine the status of any connected or existing lighting modules.
• $(SEN.LTA): Displays the status of an IR module connected to any camera port
• $(SEN.LT0... LT3): Displays the status of an IR module connected to camera port No. 1,... 4
• $(SEN.IRR): Displays the value of the existing IR illumination ring on Q71, D71 and indoor camera models
• $(SEN.WTR): Displays the value of the white light illumination ring on Q71 and D71 cameras or a white light module connected on M73 and S74

• Camera status with information about thermal sensor type (A and B)
  If thermal sensor modules are connected, the Camera Status dialog shows whether the sensor is type A or type B. This information is relevant because some functions are only supported for Type B thermal sensors.
• Double selection of the IR module
  An IR module connected to a camera port could  be selected in the Admin Menu > Hardware Configuration > Assign Wires dialog for the various options with both the IR Illuminator value and the IR Light:M<Port-No> value. This was confusing and now only the value IR Light: M<Port-Nr> is offered for selection.

Bugfixes

• RTP streaming on 12MP sensors
• When streaming 12 MP sensors via the camera's RTP server, the  maximum resolution UltraHD (2880x2880) was only available in full streaming mode if the stream was configured in the MxPEG codec. This is now also possible for H.264/H.265.
• When using the RTP server in raw streaming mode, the UltraHD (2880x2880) resolution was not available.
• Changing the camera time via the ONVIF API
  If a VMS client has changed the camera time via the ONVIF API, the camera has changed its time zone, even if the client did not request it. This could result in incorrect device time.
• Changing Video Motion Window via Genetec API
  In some cases, Video Motion windows configured through the Genetec Integration API were placed incorrectly and did not match the bounding box set in the Genetec Security Center.
• Stopping MxHUB ONVIF G Failover Recordings
  Cameras that are integrated into MxHUB via the ONVIF Integration API sometimes did not stop an ongoing ONVIF failover recording, even if MxHUB had previously reconnected to the camera.
• Registration of Smart Data Sources for MxManagementCenter (MxMC)
  After activating an App in the Setup Menu > Certified App Control > Certified App Settings dialog, the corresponding Smart Data Source is automatically added in the Admin Menu > Camera Configuration > Smart Data Configuration dialog. However, in order to transmit the information about the Smart Data Source to the MxMC for use in the MxMC's Smart Data Search, a camera restart was first required, this is no longer necessary.
• Using MxMessageSystem Event Profiles
  For certain special camera configurations, it was not possible to use more than one event profile of type MxMessageSystem .
• Configuration of the MxActivitySensor in the Japanese user interface
  When the Japanese user interface of the camera was set, the arrows for displaying the Left and Right  directions were reversed in the dialog for configuring the MxActivitySensor.
• Thermal variables for Full Image recording
  In the recorded images of a Full Image recording, the use of the following variables to determine different temperature values was incorrect: $(IMG. TRM. MIN.right), $(IMG. TRM. MAX.right), $(IMG. TRP. MIN.right), $(IMG. TRP. MAX.right). The values were not determined and entered in the image:

Known Limitations

• Graphical definition of detection areas and windows
  Due to a cache error, it can happen in the web browsers Google Chrome and Firefox that no windows or polygons can be set. Only an error message is displayed. In this case, the camera can be opened in a private window and the configuration can be carried out there.
  
• A.I.Tech Apps and Thermal Sensors
  A.I.Tech's Certified Apps cannot currently be used for thermal module video streams.
• Softbutton LEDs Blink
  The soft button function LEDsBlink is without function and does not control the LEDs of the sensor modules.
• Changing the video codec for ONVIF recordings
  Once the recording data for a particular ONVIF recording is stored, it is not currently recommended to change the video codec of the recording source. To change recording codecs for an ONVIF recording, it is recommended that you reformat the storage media
• Resolutions available via ONVIF API
  In some situations, the ONVIF integration API does not report all resolutions supported by an RTSP video stream to the camera. In most cases, this happens when the codec of an RTP video stream or the RTP server's aspect ratio is reconfigured.
  Workaround: After restarting the camera or briefly changing the integration mode, all resolutions should be offered again.

• RTP server configuration after configuration via ONVIF API
  Occasionally, the camera's RTP server configuration is not updated correctly when parts of ONVIF media profiles (called "configurations") are replaced, removed, or added by an ONVIF VMS client. This can lead to the following different effects, for example:

• Incorrect configuration values are displayed in the respective ONVIF VMS client
• RTP video, audio, or metadata streams are not displayed as configured or are not displayed at all.
• RTP streams that contain sub-streams, e.g. a metadata stream that was previously removed from the respective ONVIF media profile.

Workaround: If this issue occurs, customers should restart the camera and check the camera configuration again. If the camera configuration is still incorrect after restarting the camera, customers should try repeating the configuration changes or, if necessary, re-registering the camera in their VMS client

top

Software Release MX-V7.3.1.60 − for M7 Camera Models M73, S74, Q71, D71, c71, p71, p71TA, v71

Creation Date: 2023-01-27

Publishing Date: 2023-02-03

Enhancements and improvements

Support of the camera model p71 Thermal ECO

With this version, the new camera model p71 Thermal ECO is supported. This is an affordable basic thermal solution for indoor use, which has a wide viewing angle and covers various basic applications. These include, for example, perimeter and burglary protection as well as temperature monitoring.

S74 camera with Long Cable Extender and 12MP sensor modules

When connecting a Long Cable Extender (LCE) to a camera port of a S74 camera, the connection and operation of a 12MP sensor module to the LCE is now also supported. For that purpose, in the web browser, the value Long (> 2 meters) must  be selected for the Cable length option in the Admin > Hardware Configuration > Sensor Module Configuration dialog.

Certified Apps with improved support for the Smart Data interface to MxManagementCenter

Along with this version of the camera software, a new Certified App Package 'MX_preinstalled_apps_2023-01-27.app' was also released. This package contains all Certified Apps, including the MOBOTIX Analytics App with AI/deep learning-based object recognition. Compared to the previous version 2022-11-28, it contains improvements of the Smart Data interface to the MxManagementCenter (MxMC). Details on the exact contents of the package and the changes can be found in the release notes for the package in the Services > Download Center > All Software Downloads > Certified Apps > MX Certified Apps Release 2023-01-27 section of the MOBOTIX website (https://www.mobotix.com).

Known Limitations

• S74 cameras and MultiSense module
  When operating a MultiSense module on a S74 camera, the light sensor of the module cannot be read out after a camera restart. In this case, no lux value for the Multisense is displayed in the Camera Status dialog in the Sensors area and events in the definition of which the illumination values of this sensor are used no longer trigger!
  
• A.I.Tech Apps and Thermal Sensors
  A.I.Tech's Certified Apps cannot currently be used for thermal module video streams.
• Softbutton LEDs Blink
  The soft button function LEDsBlink is without function and does not control the LEDs of the sensor modules.
• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone, to the Line-In connector of the S74 Audio IO board and to the new Q71 model.
• RTP streaming
• When streaming 12 MP sensors via the camera's RTP server in Full Streaming Mode,  the maximum resolution in the aspect ratio "1:1" (2880x2880) is currently only available if the stream is configured to the MxPEG codec.
• When using the camera's RTP server in Raw Streaming Mode, the "UltraHD" resolution is only available on 4K Optical sensors. "UltraHD" is not supported on 12MP and 4MP ULL optical sensors.
• On MOBOTIX 7 single lense cameras (Q71, D71, c71, p71, v71) the RAW mode is currently disabled and is not supported.
• Changing the video codec for ONVIF recordings
  Once the recording data for a particular ONVIF recording is stored, it is not currently recommended to change the video codec of the recording source. To change recording codecs for an ONVIF recording, it is recommended that you reformat the storage media

top

Software Release MX-V7.3.1.57 − for M7 Camera Models M73, S74, Q71, D71, c71, p71, v71

Creation Date: 2022-11-28

Publishing Date: 2022-12-01

Enhancements and improvements

Image Quality Improvement

In this version, both the factory settings and many internal parameters important for image generation have been fundamentally revised. Thus, this software delivers much better images in many lighting situations than the previous versions. This is especially true for dark scenes and manifests itself in both improved image sharpness and lower image noise.

Improvements and changes in the area of Certified Apps

Improvements to the Smart Data Interface for MxManagementCenter (MxMC) from version 2.7

• After activating an App in the camera, it automatically enters a suitable Smart Data source in the Admin > Camera Administration > Smart Data Configuration dialog. In principle, the Smart Data interface only has to be activated once.
• In the MxManagementCenter, the camera can then use the new Get Camera Apps function to retrieve the internally required information about the activated Apps of an integrated Mx7 camera.
• The corresponding Smart Data sources are then automatically entered into the list available in the MxManagementCenter and the user can search directly for result data from these Apps in the Smart Data search of MxMC.

Updated and new Certified Apps

Along with this version of the camera software, a new Certified App Package 'MX_preinstalled_apps_2022-11-28.app' was also released. This package contains all Certified Apps, including the MOBOTIX Analytics App with AI/deep learning-based object recognition. Compared to the previous version, it includes the following new apps:

• MOBOTIX Advanced Radiometry (for the detection of temperature events)
• Mobotix Barcode Reader (for reading 1D and 2D barcodes)
• Vaxtor Genesis (for generic searching for defined texts)

In addition, some existing Apps from MOBOTIX, Visage Technologies and Vaxtor have been  replaced by new, improved versions. Details on the exact contents of the package and the changes can be found in the release notes for the package in the Services > Download Center > All Software Downloads > Certified Apps > MX Certified Apps Release 2022-11-28 section  of the MOBOTIX website (https://www.mobotix.com).

In addition, this version supports the new Mobotix Thermal Heat Detection App, which is currently only available with a French user interface and can be downloaded separately from the MOBOTIX website.

Other improvements

• Event Player
  The function icons in the Event Player view have been adapted to match the icons used in this view in the Mx6 camera line and are therefore easier to understand.
• Focusing aid
  After activating the focusing aid in the camera Quick Controls, a window can now be defined with the mouse in the image, the contents of which are then used for focusing.
• Counting Corridors of the MxAnalytics App
  When configuring counting corridors for the MOBOTIX Analytics App, the names for the flow directions are no longer limited to North and South , but can be assigned arbitrarily. In addition, deactivating the new option Count Counter Direction means that the passes in the direction of South are no longer counted and output in the report.
• FTP directory names
  When using FTP Transfer Profiles, the characters '&' and ' ' can now also be used in the FTP folder names.

Bugfixes

• Camera mode
  When changing  the camera mode in the Admin > Hardware Configuration  > Camera Mode dialog, it could happen after a camera restart using the Reboot Camera function in the same dialog that the mode was not applied completely and partly displayed incorrectly.
• Setting time and date via ONVIF
  When setting the system time and date for a camera integrated via the ONVIF protocol using the SAOP Action SetSystemDateAndTime() without specifying the time zone, the  time zone in the camera was also changed to the value "Custom/Posix", which subsequently led to error effects
• Dialog Setup Menu > Certified App Control > Certified Apps Settings
  After the first activation of the Arming option in the above dialog, the check boxes for activating the individual Apps were not displayed. After reloading the dialog, they were then available.

Known Limitations

• S74 cameras and MultiSense module
  When operating a MultiSense module on a S74 camera, the light sensor of the module cannot be read out after a camera restart. In this case, no lux value for the Multisense is displayed in the Camera Status dialog in the Sensors area and events in the definition of which the illumination values of this sensor are used no longer trigger!
  
• A.I.Tech Apps and Thermal Sensors
  A.I.Tech's Certified Apps cannot currently be used for thermal module video streams.
• Softbutton LEDs Blink
  The soft button function LEDsBlink is without function and does not control the LEDs of the sensor modules.
• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone, to the Line-In connector of the S74 Audio IO board and to the new Q71 model.
• RTP streaming
• When streaming 12 MP sensors via the camera's RTP server in Full Streaming Mode,  the maximum resolution in the aspect ratio "1:1" (2880x2880) is currently only available if the stream is configured to the MxPEG codec.
• When using the camera's RTP server in Raw Streaming Mode, the "UltraHD" resolution is only available on 4K Optical sensors. "UltraHD" is not supported on 12MP and 4MP ULL optical sensors.
• On MOBOTIX 7 single lense cameras (Q71, D71, c71, p71, v71) the RAW mode is currently disabled and is not supported.
• Changing the video codec for ONVIF recordings
  Once the recording data for a particular ONVIF recording is stored, it is not currently recommended to change the video codec of the recording source. To change recording codecs for an ONVIF recording, it is recommended that you reformat the storage media

top

Software Release MX-V7.3.1.46 − for M7 Camera Models M73, S74, Q71, D71, c71, p71, v71

Creation Date: 2022-09-01

Publishing Date: 2022-09-09

Enhancements and improvements

Support indoor models c71, p71 and v71

This software version also supports the new Mx7 indoor camera models c71, p71 and v71. In contrast to the outdoor models of the Mx7 camera line, these models can also be operated with PoE Class 3. To activate this energy-saving mode, a small switch on the camera board, right next to the RJ45 socket, must first be set to position "1" and then the PoE class 3 must be set in the web user interface. For this purpose, in the Admin Menu > Network Configuration  > Ethernet interface dialog, in the Ethernet Hardware Options section, there is the Configure PoE function button.  With its help, another dialog Power over Ethernet (PoE) is opened and there the setting of the Power Supply option can be changed  to the value Power over Ethernet (Class 3).

Whitelight module support for M73 and S74 cameras

This firmware version supports the new Whitelight module for M73 and S74 cameras. Depending on the variant, the High Power LED module can illuminate an area around the camera with a distance of up to 80 m and thus significantly increase the image quality. After connecting a Whitelight module to one of the camera ports, just like an IR Light module, it can be used in the Admin Menu > Hardware Configuration > Assign Wires dialog, by selecting the value White Light: M<Port No> for the Lights or IR Lights option, for illumination after automatic day-night switching. In the Signal Out Profiles dialog, it can also be used to define Signal Output Profiles by selecting the same value for the Signal Out Action(SO) option and thus switched on/off in response to any events.

Improvements of the Storage Failure Detection

• Monitoring of retention time
  With the help of the new Time to Keep option in the General Settings area of the Admin Menu > Storage > Storage Failure Detection dialog, the retention time set by the Time to Keep option in the Admin Menu > Storage > Storage on External File Server / Flash Device dialog can be monitored. If the retention time cannot be reached, e.g. because the existing storage area of the file server used is not sufficient and the recording therefore is running round before the retention time is reached, a notification and output of a message takes place in the log file of the Memory Failure Monitoring dialog.
• SD Card Flash Wear and I/O Error Messages
  After activating the SD card I/O option in the General Settings section of the Admin Menu > Storage > Storage Failure Detection  dialog, critical system error messages are displayed as soon as the flash wear has reached 100%. In addition, this option causes the notification of SD card I/O errors and the output of messages for I/O errors in the log file of the above-mentioned dialog.
• Monitoring the MxFFS Archive Buffer
  Activating the new Buffer MxFFS Archive option in the the General Settings section of the Admin Menu > Storage > Storage Failure Detection dialog monitors the SD card transfer buffer when stored in a (buffered) MxFFS archive. When storing in a MxFFS archive with the SD card as the primary target, a message is notified and output in the log file of the Storage Failure Detection dialog as soon as the SD card has a level of 120MByte. The messages are sent until the level has fallen below 80MByte again. When stored in a buffered MxFFS archive, the notification and message output take place as soon as the data is stored on the SD card instead of directly in the archive.

Thermal Camera Enhancements

• Ambient temperature for thermal cameras
  Decimal values can now also be specified for the Ambient Temperature to be set in the Temperature Compensation area of the Setup Menu > Thermal Sensor Settings dialog.
• SNMP OIDs for Thermal TR Measurement Windows
  For Thermal TR cameras, an additional table object statusThermalRadiometryTemperatureTable, which is specified in the MOBOTIX SNMP MIB file, is now returned via SNMP. This contains, among others, the values of the measured temperature for each defined temperature measurement window. Depending on the set Comparison Type of the TR event, the maximum or minimum measured temperature is transmitted.

Updated Certified Apps

Along with this version of the camera software, a new Certified app package 'MX_preinstalled_apps_2022-09-01.app' has also been released. This package contains all Certified Apps, including the MOBOTIX Analytics app with AI/Deep Learning-based object recognition.  Compared to the previous version, it includes some improved versions of the Apps from MOBOTIX, Visage Technologies and Vaxtor. Details on the exact content of the package and the changes can be found in the release notes for the package in the Support > Download Center > All Software Downloads > Certified Apps > MX Certified Apps Release 2022-09-01 section of the MOBOTIX website (https://www.mobotix.com).

Other improvements

• USB Power Output
  In the Admin Menu > Hardware Configuration > Manage Hardware Expansions dialog, it is possible to set the USB Power Output operating mode in the USB Connector area. By activating a previously configured USB Power Output, a device connected to the camera USB port, such as an IR radiator powered by USB, is supplied with a voltage of 5V by the camera via the USB interface. The activation can be done by an automatic day-night-switch or by executing a corresponding Signal Out Profile, for example after an assigned event. The required configuration is done in the Admin Menu >  Hardware Configuration > Assign Wires or in the Signal Out Profiles dialog by selecting the value Camera: USB Power for the corresponding option.
• Improved App stability
  When using Certified Apps of the Mx7 camera line, there could be internal camera stability problems. This was especially true for the use of several Apps at the same time and manifested itself in the following error behavior
• The list of activatable Apps in the Setup Menu > Certified App Control > Certified App Settings dialog remained empty and no Apps could be configured. After a camera restart, they were available again .
• The transmission of the App result data and its display in the MxManagementCenter (MxMC) using the Smart Data Interface no longer worked. In this case, a camera restart was necessary before camera App data could be searched for and displayed again in the MxMC.

This behavior has now been fundamentally improved so that the Apps can be displayed and used in a stable way.

Bugfixes

• S74 cameras and MultiSense module
  When operating a MultiSense module on an S74 camera, it could happen after a camera restart that values for the PIR and temperature sensor could no longer be read by the camera and thus defined events could no longer be triggered. This has been corrected and there is still a restriction with the light sensor (see below).
• Q71 Installation Mode
  Setting the Installation option  in  the vPTZ area of the Quick Controls to the Wall or Floor values was incorrect in some cases.
• Bugfixes in the area of day-night switching and IR illumination
• Day-night switching for IR-Cut Day & Night Sensor Modules
  Especially with ULL sensor modules with IR-Cut filter, the factory-set automatic day/night switching (options IR-Cut Filter and Light Switch) could lead to the camera running permanently in night or day mode after a switching process and having to be switched manually.
• Profiles ~IRLightON, ~IRLightOFF, ~IRLightToggle not usable
  When defining action groups, the internal Signal Out profiles  ~IRLightON, ~IRLightOFF, ~IRLightToggle could not be selected for actions if no MX-232-IO box or S74 IO slide-in boards were connected to the camera.
• Using the Signal Out for day-night switching
  In  the Admin Menu > Hardware Configuration > Assign Wires dialog, the use of the Value Camera: Out for the IR Lights option was incorrect and thus the Signal Out could not be used to switch on for example an external IR emitter after switching to night mode.
• LPF sensors and IR illumination
  The use of an LPF sensor did not result in the internal Signal Out Profile ~IRLightOn being permanently activated and thus permanently switching on a corresponding IR emitter or a built-in IR light module, as is necessary for the use of an LPF sensor.
• Day-night switching for separate sensors
  In the "classic" day-night switching between a color and a black-and-white sensor module, switching on the light source selected in the Admin > Hardware Configuration > Assign Wires dialog for the IR Lights  option did not work after switching to night mode.
• Multisense illumination value in camera status
  The  lux value displayed  in the Camera Status dialog in the Sensors area for a connected Multisense module was incorrect.
• Definition of SIP accounts
  When defining SIP accounts in the Admin Menu > Audio and VoIP Telephony > SIP Server Settings dialog, the error message 'Error: SIP addresses and user names must be unique.' could occur despite valid entries.
• Changing the Camera Mode
  Switching the Camera Mode in the Admin Menu > Hardware Configuration > Camera Mode dialog from Streaming to AI or vice versa was sometimes not performed correctly if the subsequent necessary camera restart was not performed manually, but via the Reboot link available in the dialog.

Known Limitations

• S74 cameras and MultiSense module
  When operating a MultiSense module on a S74 camera, the light sensor of the module cannot be read out after a camera restart. In this case, no lux value for the Multisense is displayed in the Camera Status dialog in the Sensors area and events in the definition of which the illumination values of this sensor are used no longer trigger!
  
• A.I.Tech Apps and Thermal Sensors
  A.I.Tech's Certified Apps cannot currently be used for thermal module video streams.
• Dialog Setup Menu > Certified App Control > Certified Apps Settings
  After the first activation of the Arming option in the above dialog, the check boxes for activating the individual Apps are not displayed. After reloading the dialog, they are then available.
• Online help for App dialogs
  Online help is currently only partially available in the dialogs for configuring the Certified Apps.
• Softbutton LEDs Blink
  The soft button function LEDsBlink is without function and does not control the LEDs of the sensor modules.
• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone, to the Line-In connector of the S74 Audio IO board and to the new Q71 model.
• RTP streaming
• When streaming 12 MP sensors via the camera's RTP server in Full Streaming Mode,  the maximum resolution in the aspect ratio "1:1" (2880x2880) is currently only available if the stream is configured to the MxPEG codec.
• When using the camera's RTP server in Raw Streaming Mode, the "UltraHD" resolution is only available on 4K Optical sensors. "UltraHD" is not supported on 12MP and 4MP ULL optical sensors.
• On MOBOTIX 7 single lense cameras (Q71, D71, c71, p71, v71) the RAW mode is currently disabled and is not supported.

top

Software Release MX-V7.3.1.31-r3 − for M7 Camera Models M73, S74, Q71, D71

Creation Date: 2022-06-28

Publishing Date: 2022-06-30

Enhancements and improvements

ONVIF-G

With this software version, the M7 camera models support the ONVIF-G standard. This allows these cameras to use the ONVIF-G protocol to configure edge recording on the camera's internal SD card and then access the data stored in this way. Some video management systems, such as e.g. MOBOTIX HUB, use this function to implement a so-called "fail-over recording". With that the failure of a storage server is briefly bridged by an edge recording on the camera.

Updated and new Certified Apps

Along with this version of the camera software, a new Certified App package 'MX_preinstalled_apps_2022-06-21.app' has also been released. This package contains all Certified Apps, including the MOBOTIX Analytics App with AI/Deep Learning-based object recognition.  Compared to the previous version, it also includes revised versions of the Apps from FFGroup, Vaxtor and Iristy, a new App from Vaxtor (USDOT) as well as two new Apps from MOBOTIX for color recognition (Mobotix Color Recognition) and AI-based motion detection (Mobotix ActivitySensor). Details on the exact content of the package and the changes can be found in the release notes for the package in the Support > Download Center > All Software Downloads > Certified Apps > MX Certified Apps Release 2022-05-31 area of the MOBOTIX website (https://www.mobotix.com).

Other improvements

• SNMP support
  With this version, SNMP clients can also receive various temperature values from thermal cameras via the SNMP protocol. The SNMP-MIB file of the camera has been extended by corresponding OIDs 'MOBOTIX-MIB::statusThermal*'.
• Maximum text font size
  The maximum size of the text fonts for text overlays in the live image or image profiles has been increased from 24pt to 48pt.
• Online help Integration Protocols
  The online help of the dialog Admin Menu > Camera administration > Integration Protocols has been expanded and improved in many places.

Bugfixes

• PoE switches with PoE class3 (correction in 7.3.1.31-r3)
  For network switches that return an incorrect PoE class (PoE3 instead of PoE+) during the negotiation phase, the camera version 7.3.1.31-r1 did not support the operation of additional resources such as an IR module.
  
• IR module with LPF sensor module (correction in V7.3.1.31-r3)
  The operation of an IR module together with an LPF sensor module was not possible in version 7.3.1.31-r1.
  
• Update of older software versions with activated App Object Recognition (correction in V7.3.1.31-r3)
  If an older software version was updated to version 7.3.1.31 or 7.3.1.31-r1 on a camera with App Object Recognition enabled, without first disabling this App and resetting the camera to "Streaming" mode, some combinations of firmware and App version could lead to problems: the camera then restarted again and again after a few seconds of uptime.
  
• Further WDR improvements
  In special lighting situations, the following effects could still occur when WDR is activated: short-term black image, unstable exposure control, image flickering (fast change between brighter and darker image with increased MxPEG rate).
• Camera restarts when combining Apps and thermal modules
  For cameras with a thermal module connected to Port1 or Port2, activating the Certified Apps led to a regular (every 5min) restart of the camera.
• Day-night switching for IR-Cut Day & Night Sensor Modules
  Depending on the software version, the factory-set automatic day/night switching (options IR-Cut Filter and Light Switch) for IR-Cut Day & Night sensor modules could lead to the cameras running permanently in night mode (from V7.2.1.x on) or day mode and had to be switched manually.
• Variables $(SEN. TC0. CELSIUS),... $(SEN. TC3. CELSIUS) in image profiles
  The temperature variables $(SEN. TC0. CELSIUS),... $(SEN. TC3. CELSIUS)to display the temperature, e.g. of a MultiSense module, were not displayed with their current values but empty when used in image profiles.
• Camera mode AI and exposure settings
  When operating the camera in AI mode, not all options were available in the Setup Menu > Image Control > Exposure Settings dialog. Among other things, the definitions of the exposure windows were missing.
• Dark page layout and formatting wizard
  When using the Dark Theme in the camera's graphical user interface, some options were difficult to see in the Formatter Wizard: MxFFS Volume Partitioning dialog.
• System messages for LPF sensor modules
  During the operation of LPF sensor modules, incorrect entries "EVENT IR Light Switched on" occurred in the system messages.
• Activation of a MultiSense PIR event in the MxMC
  The PIR sensor of a MultiSense module connected to the camera could not be used to activate PIR-events in the camera by the MxManagementCenter.

Known Limitations

• S74 cameras and MultiSense module
  When operating a MultiSense module on a S74 camera, the sensors of the MultiSense module may no longer deliver values to the camera after a camera restart.
  
• A.I.Tech Apps and Thermal Sensors
  A.I.Tech's Certified Apps cannot currently be used for thermal module video streams.
• Dialog Setup Menu > Certified App Control > Certified Apps Settings
  After the first activation of the Arming option in the above dialog, the check boxes for activating the individual Apps are not displayed. After reloading the dialog, they are then available.
• Online help for App dialogs
  Online help is currently only partially available in the dialogs for configuring the Certified Apps.
• Softbutton LEDs Blink
  The soft button function LEDsBlink is without function and does not control the LEDs of the sensor modules.
• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone, to the Line-In connector of the S74 Audio IO board and to the new Q71 model.
• RTP streaming
• When streaming 12 MP sensors via the camera's RTP server in Full Streaming Mode,  the maximum resolution in the aspect ratio "1:1" (2880x2880) is currently only available if the stream is configured to the MxPEG codec.
• When using the camera's RTP server in Raw Streaming Mode, the "UltraHD" resolution is only available on 4K Optical sensors. "UltraHD" is not supported on 12MP and 4MP ULL optical sensors.
• On MOBOTIX 7 single lense cameras (Q71, D71) the RAW mode is currently disabled and is not supported.

top

Software Release MX-V7.3.0.54 − for M7 Camera Models M73, S74, Q71, D71

Creation Date: 2022-03-03

Publishing Date: 2022-03-04

Enhancements and improvements

Support for the new Q71-Hemispheric camera model

This version supports the new MOBOTIX 7 camera model Q71-Hemispheric. The camera has a 12-mega-pixel image sensor with integrated IR cut filter, a hemispheric lens, microphone and speaker, as well as integrated LEDs for IR and White Light Illumination. Compared to the M73 and S74 camera models, the following software functions are available:

• Setting of different Display Modes with automatic image correction (Normal, Surround, Panorama, Panorama Focus, Double Panorama) in the Quick Controls  or in  the Setup Menu > Image Control > General Image Settings dialog
• Selection of additional resolutions (12MP 1:1 (2880x2880), UltraHD²(2144x2144), FullHD²(1080x1080), HD²  1:1(768x768), nHD²1:1(360x360)) in the Quick-Controls or in the Setup Menu > Image Control > General Image Settings dialog
• Setting of the installation (wall, ceiling, floor) in the vPTZ area of the  Quick Controls
• Activation of the integrated IR and White Light LEDs
  These integrated illuminations are activated in the Admin Menu > Hardware Configuration > Assign Wires dialog. In the factory settings, the options are set as follows:
• Lights = White Light Ring
• IR Lights = IR Light Ring

With this setting, IR illumination is used after an automatic day-night switching (also factory set) in night mode. If White Light Illumintaion is to be used in night mode and the camera shall continue to produce a color image, the following options must be set:

• IR Lights = White Light Ring
• IR-Cut-Filter = IR-Filter-On (in the Setup Menu dialog > Image Control > General Image Settings)

For testing and quick switching on/off the two types of lighting, two suitable Shortcuts are also defined ex works in the title bar of the web browser's live view (see section "Shortcuts for soft button functions" below).

The other software functions are identical to those of the M73 and S74 models.

Support of the new camera model D71 - Single Lens Dome

This version supports the new MOBOTIX 7 camera model D71 - Single Lens Dome. The camera is available with a 4K UHD or 4MP ULL sensor, each with integrated IR cut filter, has a 3-axis pan-tilt head (manual adjustment), microphone and speaker, and integrated IR illumination. The activation of the integrated IR illumination also succeeds here in the Admin Menu  > Hardware Configuration > Assign Wires dialog. From the factory, the IR Lights option is already set to the value IR Light Ring and thus the IR illumination is automatically used to generate the black and white images in night mode.

The other software functions are identical to those of the M73 and S74 models.

Support of the new hemispheric 12MP sensor modules

For use with an S74 camera, there are now also hemispheric sensor modules with a resolution of 12MP and integrated IR cut filter availabe. The connection, configuration and use of these modules are completely analogous to the non-hemispheric sensor modules. The correction-specific software functions, such as e.g. the setting of the installation type or the use of the corrected Display Mode, are identical to the functions in the new hemispheric Q71 camera model (see above).

Support of the new Thermal Eco module

Multiview view

The familiar Multiview view for displaying live images and the latest event images from one or more cameras in the web browser is now also available in the new graphical user interface. This view is activated via the new function icon on the right side of the title bar. After activating this view, the function icon   for configuring the Multiview views appears. The actual configuration and use of the Multiview views do not differ from the Multiview views of the previous software versions.

LED Configuration

The Admin Menu > Camera Administration > LED Setup dialog contains an additional section LED Order and Settings for the individual configuration of the camera LED and the LEDs of all sensor modules connected to the camera.

Software Update

App license management

Using the new Admin Menu > Camera Administration > Manage App Licenses dialog, the required licenses for integrated Apps can now also be requested and activated directly from the camera. As in the MxManagementCenter, both offline and online activation is also possible here.

Improvements to the new graphical user interface

The following improvements have been implemented for the new graphical user interface for web browsers introduced with version 7.2.1.29:

• Title bar
  The title bar is now not drawn transparently and thus all symbols contained in it are always clearly recognizable. In addition, the icon for deactivating/activating PTZ actions in the activated state is no longer crossed out.
In the Admin Menu > Page Administration > Language and Start Page dialog, there is a new section Shortcuts. There, one or two soft button functions can be defined, which can then be selected using additional icons on the right side of the title bar of the web browser window.

• Visual Alarm Profiles
In the Logos and Image Profiles section of the Admin Menu there is now an additional link Visual Alarm Profiles. This allows these profiles to be edited faster than before, for example to be used in SNMP Alarm Traps (see next section).
• Event Player
  The function icons in Event Player mode are now easier to recognize.
• Event overview
  In the Setup Menu > Event Control > Event Overview dialog, the active events are now easier to recognize.
• Camera Mode dialog
  The Admin Menu > Hardware Configuration > Camera Mode dialog has been improved so that it is no longer possible to trigger a camera reboot from the dialog without permanently saving the changes made beforehand.
• Configuration of the Certified Apps
  When using a Dark Theme, the bright areas of some dialogs for configuring Certified Apps (e.B. Vaxtor LPR) are now easier to read.
  
  

Enhanced SNMP Traps

Alarm Traps

Visual Alarms, which are linked to individual events via Action Groups, can now be used to generate SNMP Alarm Traps.  These are then sent to the SNMP client when one of the associated events is triggered. In addition, an SNMP trap can also be generated for acknowledging the visual alarms.

To configure such SNMP Traps, the following steps are necessary:

• Configuring SNMP
• Creating a Profile  (e.g. "VA Permanent") for a Visual Alarm with the following properties
• Name = VA Permanent (example)
• Display time = Unlimited
• Alarm Acknowledgement = Enabled
• Send SNMP Trap = Activated
• Create an Action Group with the following properties:
• Name = VA Permanent (example)
• Action 1 = Visual Alarm: VA Permanent
• Event selection = <selection of the desired events, including "Signal: UC" for testing >

Subsequently, the triggering of SNMP Traps via a Visual Alarm and its acknowledgement can be tested as follows:

• Activation and operation of the soft button "UC Event" (= factory setting)
• Activation and activation of a soft button "Acknowledge"

Alternative:

• Activation and operation of a shortcut (see above) "UC Event" in the title bar
• Activation and operation of a shortcut (see above) "Acknowledge" in the title bar

Additional:

• Show the variable $(EVT. VATIMESTAMP) in the live image to display the timestamp of the last acknowledgement of a Visual Alarm
• Signaling of the Visual Alarm via the camera LEDs (see above), e.g. selection Visual Alarm as a value for LED Main Switch

This creates the following SNMP trap OIDs:

    .1.3.6.1.4.1.21701.3.5.1 --> visualAlarmNew

  .1.3.6.1.4.1.21701.3.5.2 --> visualAlarmCleared

Error Messages

Certain camera error messages can now also be sent as SNMP Traps to a connected SNMP client. For this purpose, the following dialogs have been extended by an additional option SNMP Traps:

• Admin Menu > System Information > Error Notification, each with an option in the Notification and Notification After Reboot sections
• Admin Menu > Storage > Storage Failure Detection, in the Notification section
• Admin Menu > Network Setup > Web Server, in the Intrusion Detection Settings section

Extended text variables

• New temperature variables with additional formats
  For a more flexible display in the live image and better use in camera API calls, new temperature variables have been added. In addition to the existing variables
      '$(SEN.<Sensor type>.Celsius)' and '$(SEN.<Sensor Type>.Fahrenheit)'
  it's now possible to use the new variables
      '$(SEN.<Sensor Type>.<Unit>.<Format>)'.

• Unit from {'Celsius', 'C, 'c, 'Fahrenheit', 'F', 'f', 'Kelvin', 'K', 'k'}
• Format from {'INT', 'I10', ''F10', 'F41', 'F72', 'NUM'} with the following meanings:
• INT: Output as an integer with possibly negative sign
• I10: Output of the value multiplied by 10 as an integer with possibly negative sign
• F10: Output of the value as an integer with at least one place and with sign
• F41: Left-aligned output with at least 4 digits, with 1 decimal place and sign
• F72: Left-aligned output with at least 7 digits, with 2 decimal places and signs
• NUM: Output as a decimal number with decimal places with possibly negative sign - specially designed for use within JSON expressions
• Examples of a measured Thermal TR temperature value of +56.7 C°:
• $(SEN.TTR.C.INT) => "56"
• $(SEN.TTR.C.I10) => "567"
• $(SEN.TTR.C.F41) => "+56.7"
• $(SEN.TTR.C.F72) => "+56.70 "
• $(SEN.TTR.C.NUM) => "56.7"

• 'SKIP'option for text variables
  The '$(<Variable>, SKIP=<Number>)' option skips the first <number> characters of the value of <Variable> in the output. For a negative <number> the characters of the variable value are skipped from the end.
• Temperature variables for different Thermal Measurement Windows
  In addition to the variables $(SEN.TTR.CELSIUS/FAHRENHEIT)now also the variables $(SEN.TTR.0. CELSIUS/FAHRENHEIT), $(SEN. TTR.1.CELSIUS/FAHRENHEIT),... $(SEN.TTR.<(number of measurement windows)-1>.CELSIUS/FAHRENHEIT) are available to determine the specific temperature values in the individual Measurement Windows 0,... <(number of measurement windows)-1>.

Updated and new Certified Apps

Along with this version of the camera software, a new Certified App package 'MX_preinstalled_apps_2021-12-14.app' has also been released. This package contains all Certified Apps, including the MOBOTIX Analytics app with AI/Deep Learning-based object recognition. Compared to the previous version, it also includes revised versions of the Apps from A.I. Tech, FFGroup and Vaxtor, as well as two new Apps from Vaxtor for the recognition of aircraft identification numbers and license plates, a new App from  FFGroup  for license plate recognition and a new App from Irisity for the detection of burglaries. Details on the exact content of the package and the changes can be found in the release notes for the package in the section Support > Download Center > All Software Downloads > Certified Apps > MX Certified Apps Release 2021-12-14  of the MOBOTIX website (https://www.mobotix.com).

Other improvements

• Camera Support Information
  Downloading the support information using the Admin Menu > System Information > Download Support Information dialog now generates a file in the format '.tgz' instead of '.eml' as before.

Bugfixes

• Image flickering at WDR
  When WDR was activated, minor changes in illumination could lead to a change in the internal exposure parameters, which was noticeable in the form of a single image frame that was too bright as a short flare-up.
• Problems with the classic design
  When the camera start page was displayed in the Historical Layout, the event list was not filled in the Event Player view.  In addition, in this setting, no detection areas could be created in the live image for some Certified Apps (e.g. FFLPR MMC). 
• Thermal events after camera restart
  Thermal sensors could cause thermal events configured after a camera restart to be triggered incorrectly.
• Variables $(ID.ET0)/$(ID.FIP)
  When the variables $(ID.ET0) and $(ID.FIP) were used together in this order, the current camera IP address was returned twice instead of the current IP address and factory IP address.
• Microphone and Speakers dialog
  The description text for the Option Announce network data in the Admin Menu > Audio and VoIP Telephony > Speaker and Microphone dialog of an M73 camera contained an error (using the "R button").
• Window definitions in dual image
  When using the camera selection Both (dual image), no windows could be defined for the left image sensor in the functional areas Activity Sensor, Video Motion Detector (VM) and Exposure.  
• Exposure window in the Quick Controls
  After defining an exposure window using the Quick Controls, an empty white window was sometimes displayed.
• Image settings
  The changes to settings in the Setup Menu > Image Control > General Image Settings dialog were then not displayed correctly in the corresponding fields of the Quick Controls. This has been corrected, but a reload of the browser window is still necessary for the correct display in the Quick Controls.
• Admin and Setup Menu
  When the Admin Menu and Setup Menu dialogs were reopened, previously collapsed or collapsed areas were not displayed correctly opened or closed according to the last status.
• PI event
  In the Setup Menu > Event Control > Event Overview dialog, a PI event was entered in the Environment Events section, even if no MultiSense module with PIR sensor was connected.
• Format Storage Medium dialog
  The Format Storage Medium dialog, which can be used in the Event Player view when downloading events, contained the invalid RAM Buffer selection option.

Known Limitations

• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone, to the Line-In connector of the S74 Audio IO board and to the new Q71 model.
• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.

top

Software Release MX-V7.2.1.29 − for M7 Camera Models M73, S74

Creation Date: 2021-08-20

Publishing Date: 2021-08-31

Enhancements and improvements

Uniform software for different camera models and apps (camera mode)

The installation file of this software version can be used for updating M73 and S74 models alike. It also directly supports the use of the App MOBOTIX Analytics with AI/deep learning-based object recognition. After installing this App (see below), only the option Camera Mode in the new Admin > Hardware Configuration > Camera mode dialog has to be changed from Streaming to AI . After a subsequent camera reboot the App can then be activated and via the Setup > Control for Certified Apps > Settings for Certified Apps dialog.

New graphical user interface for web browsers

The layout and operation of the HTML pages for controlling the camera using a web browser have been fundamentally revised and improved. The structure of the dialogues and their context have not been changed! The following describes the most important changes compared to the previous versions.

Camera Start Page

• Contents

In addition to the live camera image, the start page now contains only a partially transparent title line with the following elements::

• Menu selection at top left : This opens a dialog for selecting all Quick Controls and all Soft Buttons, including Admin Menu and Setup Menu

• PTZ actions : With this symbol, PTZ (Pan-Tilt-Zoom) actions can be (de-)activated with the mouse in the live image.
• Pause live image : This allows the live display of the camera image to be paused in the browser, for example to reduce computer usage, or to capture a detail in the current camera image.
• Save image : This feature saves the current live camera image.
• Camera online help : This opens the HTML online help of the camera.
• Camera status : Clicking on this icon opens the Camera Status dialog.
• Player view : Here you can switch between the Live and Player View.

• Design Settings

• Theme: to switch between a dark and light background
• Layout: to switch between the new and classic layout of the start page
• Window Opacity: to change the transparency of the individual dialogs

• Scaling

• Soft-Buttons

After displaying the Soft-Buttons by opening the menu in the upper left corner of the start page, the edit mode for the Soft-Bbuttons can be opened via the lock symbol in the lower left corner. The positions of the individual Soft-Buttons can now be changed by drag & drop with the mouse. In addition, by pressing the symbol   at the bottom left, a list of the defined Soft-Buttons is displayed, from which a Soft-Button can be inserted by drag & drop with the mouse into the Soft-Buttons list of the start page.

Structure and operation of the dialogues

• Window areas
  The window areas of the individual dialogs are now all limited to the display area of the camera window in the web browser.
• Parameter areas
  The individual parameter areas for grouping certain options within the dialogs are folded in by default and can be opened and closed again via the Symbol in the right corner of the area title line. The camera SW uses browser cookies to remember the state of the dialogs and restores it after closing and reopening a dialog.
• Graphical definition of windows in the camera image
  At all points for the definition of window areas within the camera live image (e.g. when defining exposure windows) there is now no need to use a key combination ("Shift + Click", "Click").  Instead, after pressing the respective button for adding an area (e.g. the Add Exposure Area button in the Setup > Image Settings > Exposure Settings) dialog, the windows can be mounted directly with the mouse. All stretches of the rectangle defined by this contain "active centers", which can be moved with the mouse and thus used to define polygons.

Editing the camera configuration (only for experts!)

• Using the Admin > Configuration > Edit menu entry, the new Kurator dialog is now opened, with the JSON-based view of the camera configuration for reading and modifying configuration entries.
• Via the menu entry Admin > Configuration > Text Edit, the Edit Configuration File dialog can still be opened, with the classic file view, grouped by "Sections", for reading and changing the camera configuration.

Online Help

The online help has been adapted to the changed user interface and in individual dialogs additional additions and changes have been made.

MOBOTIX HUB connection with failover recording on the SD card

Depending on the settings of the failover recording in the Management Client of MOBOTIX HUB, the data between the SD card and the recording data of the recording service, is then, either manually or automatically, synchronized by the recording service. In both cases, the data stored on the SD card during the failure is read by the camera and transferred to the server database.

Support of thermal sensor modules together with audio modules

Improvements in the area of Certified Apps

Unified installation package

Along with this version of the camera software, a new Certified App package 'MX_preinstalled_apps_2021-05-27.app' has also been released. This package now includes all Certified Apps, including the App MOBOTIX Analytics with AI/deep learning-based object recognition. Compared to the previous version, it also includes revised versions of the Apps from A.I. Tech., FFGroup, Vaxtor and Visage Technologies, as well as new Apps from Vaxtor for identifying railway wagons with UIC codes and from FFGroup for identifying vehicle characteristics (MMC). For details on the exact content of the package and the changes, see the release notes for this package in the Certified Apps > MX Certified Apps Release 2021-05-28 section of the MOBOTIX Beta website (https://www.mobotix.com/de/beta).

New functions in the Settings dialog for Certified Apps

In the Setup > Certified App Control > Certified App Settings dialog, the following extensions have been integrated:

• Resource monitor
  With this new option, the current utilization of the camera resources can be displayed in the live image. Selecting the option displays the current values for the maximum frame rate, memory used, CPU usage, and even active Apps. This allows the camera load to be monitored, especially in the case of several activated Apps. If necessary, an overload, which may lead to a camera restart, can be avoided then by the targeted deactivation of individual Apps.
  
• Custom text fonts
  With the help of the new Custom font option and the new Manage Font File dialog, which is opened via the Manage Font File link in the above dialog, you can load your own text fonts into the camera and select them for the display of app-specific texts in the live image. This allows, for example, identified license plates with Arabic characters to be displayed correctly in the image.

• Deleting Apps
  Using the Delete application button behind each App, the App in question, including the data generated by it, can be deleted  from the camera.

WDR-Funktion

The Wide Dynamic Range function for handling large differences in brightness in the image has been further significantly improved compared to the previous version using a different calculation method. In particular, dark areas of the image are now displayed better and there is less color distortion than before. The WDR function is still activated using the  Wide Dynamic Range option in the Setup > Image Control > Exposure Settings dialog whereby only a distinction is made between the values On and Off. If required, the previous WDR algorithm with its 4 setting options (Default,  Moderate, Strong and Aggressive) can also be activated for special application situations by selecting the value On(Legacy).

Other improvements

• IR light module together with LPF module
  By activating an LPF sensor module, an IR light module also connected to the camera is now automatically switched on at all times.

Bugfixes

• RTSP-Streaming
  If only one image sensor module was connected to a M73 or S74 camera, the streaming mode Raw could not be selected.
• Setting the image quality with ONVIF integration
  During an ONVIF integration of the camera, the information about the current setting of a constant bit rate (value of parameter RateControl.ConstantBitrate) was in some cases not properly returned to the ONVIF client. In addition, the ONVIF setting of a constant bitrate (by the same parameter) for streams with video codec setting H.265 was incorrect.
• Secure SD card formatting
  Formatting the camera's internal SD card using the Secure Deletion mode could lead to a termination of the function and subsequent restart of the camera.
• Camera restarts when using Apps
  If several apps were activated in the camera at the same time, the camera could restart.

Known Limitations

• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone and the Line-In connector of the S74 Audio IO board.
• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.

top

Software Release MX-V7.1.3.19 − for M7 Camera Models M73, S74

Creation Date: 2021-03-17

Publishing Date: 2021-03-31

Improved and additional Certified Apps

This release has improved and partially expanded existing Certified Apps and added new apps.

Vaxtor ALPR MMC LPR V1.2.1(*new*)

• Detection of single- and two-line flags
• Identification of signs with Latin, Arabic and Hebrew characters.

Vaxtor Containers V1.2.1 (updated)

With this new version of the App for the detection of transport container codes according to ISO 6346, the analysis can now also be done on a live camera dual image.

Vaxtor LPR V1.1.2 und ADR V1.1.2 (updated)

Visage Technologies Facial Recognition V1.2 (already contained in App-Package 2021-02-24)

Firmware 7.1.3.19 now also supports this version of the app, in which some bugs have been fixed and performance improved. In addition, facial recognition now works much more robustly in demanding conditions such as large scaling variability, difficult lighting, certain poses and covers such as beards, glasses and  masks. In firmware version 7.1.3.15, this App version could not be used yet.

Improvements

• Section Apps in Camera Status
  In the Camera Status dialog, there is a new Apps section.  There, the version of the loaded App package as well as the maximum SD card storage for Apps and the storage currently occupied by Apps are displayed.
  
  

Bugfixes

• MultiSense temperature with negative values
  When using a MultiSense module to determine the ambient temperature, negative values below 0°C were displayed in the variable $(SEN. TCx.CELSIUS)only as 0°.
  
• Acticity-Sensor Events in Thermal Cameras
  Using self-defined detection ranges for the Activity Sensor could cause the triggering event to be displayed in the image in the wrong position.
• ONVIF -Integration
  An ONVIF integration of the camera could cause problems in certain VMS applications (e.g. Avigilon ACC) due to an error in the requested H.265 profile.

Known Limitations

• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone and the Line-In connector of the S74 Audio IO board.
• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.
• RTSP-Streaming
  If only one image sensor module is connected in the M73, the streaming mode  Raw cannot be selected at this time.

top

Software Release MX-V7.1.3.15 − for M7 Camera Models M73, S74

Creation Date: 2021-01-26

Publishing Date: 2021-01-28

Improved and additional Certified Apps

This release has improved and partially expanded existing Certified Apps and added new apps.

FF Group V1.2

• With this version of the App, license plate recognition is also possible when the camera creates a dual live image.
• In addition, the list of supported countries has been extended to include South Africa, Taiwan, Vietnam, Indonesia and Hong Kong
  

Vaxtor ADR V1.1.1

Vaxtor LPR V1.1.1

With this new version of the App for the recognition of license plates, the following improvements have been implemented:

• Improved identification of license plates with Arabic letters.
• Enlarged database for the detection of German city and district codes. Previously, some license plates (e.B RA, BH, KA,...) could not be identified and did not trigger an event.

Known Limitations

• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone and the Line-In connector of the S74 Audio IO board.
• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.
• RTSP-Streaming
  If only one image sensor module is connected in the M73, the streaming mode  Raw cannot be selected at this time.

top

Software Release MX-V7.1.3.11 − for M7 Camera Models M73, S74

Creation Date: 2020-12-11

Publishing Date: 2020-12-16

Improvements

• WDR (Wide Dynamic Range) function with test option
  After activating the WDR function in the Setup > Image Control > Exposure Settings dialog, a further improvement of the image quality in difficult lighting situations can be achieved, there using the new Experimental Exposure Settings option.  In particular, over-exposures can be avoided after rapid changes in brightness in a small area of the image.

Note

This option has been integrated for testing purposes and is not yet suitable for productive use, as there may still be image problems when used.

• Access data for file servers
  The password of a file server defined for storage in the Admin > Storage > Storage on External File Server / Flash Device dialog can now also contain the special character '#'.

Bugfixes

• Switching signal output after S74 camera restart
  For S74 cameras a configured signal output was switched on for a short while (< 1s) after a camera reboot.
  
• Dual Image in the MxManagementCenter (MxMC)
  When displaying a camera dual image in the preview mode of the MxMC (e.g. in the view Research or in the dialog Clip and Recording Configuration) the left and right camera images were swapped.
• Image Programs
  The selection of an Image Program in the quick controls of the camera live view in the web browser resulted in an error message and the corresponding settings were not applied.
• Signal output for firmware with AI/deep learning-based object detection
  When using the firmware to support MOBOTIX Analytics with AI/Deep Learning-based object detection,  the signal output switch of a M73 camera was without function.

• Thermal and WDR
  In the Setup > Image Control > Exposure Settings dialog, WDR could also be activated for a thermal sensor and switching on this option had no effect. The WDR function has been removed in this case.
  

Known Limitations

• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone and the Line-In connector of the S74 Audio IO board.
• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.
• RTSP-Streaming
  If only one image sensor module is connected in the M73, the streaming mode  Raw cannot be selected at this time.

top

Software Release MX-V7.1.2.24 − for M7 Camera Models M73, S74

Creation Date: 2020-10-26

Publishing Date: 2020-10-27

Enhancements and Improvements

Support of Camera Model S74 and other Function Modules

This version supports the new MOBOTIX 7 camera model S74. It is a robust camera with a die-cast aluminum housing, specially designed for concealed installation, offering connectivity for up to four different image sensor and function modules. Just like the M73 camera, the S74 can alternatively be operated with one or two optical image sensor modules, with a Thermal (-TR) sensor module alone, or with a Thermal(-TR) sensor module together with an optical image sensor module. In addition, up to two IR-Light modules and/or other new function modules (see next section) can be combined with the image sensors. Cables with a length of 1, 2, or 3 meters are available for connecting the image sensor and function modules.

In addition, the following new function modules for M73 and S74 camera models can be used with this firmware.

MultiSense Module (M73 und S74)

This function module for M73 and S74 cameras each features a light, temperature and passive infrared sensor and an integrated microphone. Just like the IR Light module, it can be connected to any of the 4 ports M1 to M4. The sensors are used to define events as usual in the Setup > Event Control > Event Overview > Environment Events dialog. After connecting several MultiSense modules to an S74, when configuring an ambient sensor the relevant connection port of the MultiSense module belonging to the sensor can be selected as the Sensor Source.

Audio Module (M73)

With this new function module, M73 cameras have the usual audio functions, such as audio output and audio in the video recordings. After connecting the module, the audio is set up as usual in the Admin > Audio and VoIP Telephony > Microphone and Speaker dialog.

Audio/IO-Board (S74)

This allows an S74 camera to be extended with audio as well as switching input and output functions.

For the audio output, either the connector can be used to connect a (passive) speaker, or the line-out port can be connected to the line-in port of an audio amplifier. As an audio input, a microphone can be connected directly, or the line-in port can be connected to the line-out port of an audio output device (e.g. PC or smartphone). The desired audio functions are also configured after installing the board in the camera in the Admin > Audio and VoIP Telephony > Microphone and Speaker dialog.

In addition, an input signal and a potential-free output switch (relay function) can be used with this board to control external devices. After installation of the board, input and output signals can be used as usual to define a signal event or signal output profile.

New WDR Function

By implementing a completely new algorithm, compared to the previous version, the behavior of the Wide Dynamic Range function for handling large differences in the image's brightness has been further significantly improved. The WDR function can be activated in the Setup > Image Control > Exposure Settings dialog. When WDR is activated, the settings that are not needed, such as Exposure Windows and Target Brightness, are automatically hidden. To adapt to the current scene, 4 different Contrast Enhancement Levels are available:  Default, Moderate, Strong and Aggressive. The default setting when activating WDR is Default and the further the value is changed in the direction of Aggressive, the more details can be seen even with large brightness differences. This is associated with an increasing change in the color characteristics in the image.

4MP-Ultra-Low-Light-Sensor

Functional Improvements and Enhancements from the Mx6 Camera Series

• Cyber Security and Network
• Storage
• Transfer Profiles

Other Improvements

• ONVIF Enhancements
  When integrating the camera into other systems via ONVIF interface, an audio back channel is now also supported.
• Certified Apps
  With this version, the existing Certified Apps have been revised and improved. Regarding the installation and configuration of the Apps, nothing has changed compared to the previous version 7.0.6.18. All Apps are now listed in the Setup > Certified App Control > Certified App Settings dialog with a specific version number..
• Online Help
  The integrated online help of the camera has been revised and supplemented in several areas, especially in the areas of thermal functions, MOBOTIX Analytics with AI-based object detection and the A.I. Tech Apps.

Bugfixes

• Thermal TR events with Temperature Range
  The use of a temperature range instead of a threshold value to trigger thermal TR events was incorrect.
• MOBOTIX Analytics
  Using more than one counting corridor could produce incorrect counting values.
• Day-night switching for IR-Cut Day & Night Sensor Modules
  Switching between the day and night mode of these sensor modules could lead to misconduct if the lighting conditions changed shortly after a day-night switch or if a change in image settings was made.
• Color saturation
  The color saturation setting had no effect on the camera image.

Known Limitations

• Switching output after S74 camera restart
  For S74 cameras a configured signal output is switched on for a short while (< 1s) after a camera reboot.
• Microphone Event
  Currently, no microphone event is supported. This applies to the built-in microphone in the Audio and MultiSense module as well as to a connected microphone and the Line-In connector of the S74 Audio IO board.
• Thermal and WDR
  In the Setup > Image Control > Exposure Settings dialog, WDR can also be activated for a thermal sensor and switching on this option has no effect.
  
• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.
• RTSP-Streaming
  If only one image sensor module is connected in the M73, the streaming mode  Raw cannot be selected at this time.

top

Software Release MX-V7.0.6.18 − for M7 Camera Model M73

Creation Date: 2020-09-15

Publishing Date: 2020-09-18

Enhancements and Improvements

Improved and additional Certified Apps

This release has improved and partially expanded existing Certified Apps and added new apps

MOBOTIX Analytics

Analytics without additional function
This version makes the MxAnalytics functions, known from previous camera lines, available for the first time within a pre-installed royalty-free App. As with all other Apps, activation and configuration is done via the Setup > Certified App Control > Certified App Settings dialog.

Analytics with object recognition
In addition, the new Use AI component option enables object recognition based on AI/Deep Learning techniques. For example, you can distinguish between different types of objects, such as cars, trucks, people, etc. To use this feature, a special software package must be installed on the camera (see following note). After installing this package, the  Use AI component option and the additional Object Recognition Settings  app are available to configure AI-based object detection.

A.I.Tech Apps

• New 3rd Party VMS interfaces now allow the direct integration of A.I. Tech App Events into wavestore and Qognify Cayuga systems.
• Embedded Dashboard no longer needs to be activated separately, the interface is automatically activated after the App is started.
• The online documentation of the A.I. Tech Apps can now be accessed directly from the web interface.

• In this release, a new 3D calibration mechanism has been introduced that allows you to get visual feedback about the procedure performed and to immediately detect errors made during the configuration procedure.

• A new facial recognition mechanism based entirely on deep learning is now available in the AI-BIO-DEEP App. This extension allows for greater accuracy in facial recognition and makes detection less susceptible to potential interference.
• In order to adapt the performance of the App to the needs of the customer, you can now choose between different neural networks for facial detection

• The update adds a new deep learning-based neural network to the App to detect falling people, further improving the App's accuracy.

• The App now includes an even more powerful yet more efficient classification mechanism that increases accuracy and detection speed.

Visage Technologies (VT) Face Recognition App

• Faces can now be mapped to an "Granted" or "Denied" list while learning.

FF Group und Vaxtor LPR Apps

• This means that two additional License Plate Recognition (LPR) Apps are now available.

General improvements

• Errors when activating a Certified App, e.g. due to a faulty connection to the license server, are now logged in the system messages.

Bugfixes

• Setting the image sensor for thermal cameras
  For Thermal cameras the setting of the image sensor in the Admin > Hardware Configuration > Image Sensor Configuration dialog was incorrect in certain cases.
• MxActivity Sensor Events in Thermal Cameras
  Using MxActivity events with defined detection ranges could cause thermal cameras to fail when moving outside the defined areas.
• Thermal TR temperature at left image
  When using a Thermal TR module as a left image sensor, incorrect temperatures (e.g. 2000°C) were sometimes displayed as a temperature reading after a camera restart.
• Visage Technologies Face Recognition App
  This app could cause permanent false triggers under certain conditions and lighting conditions.
• A.I.Tech App Dashboard
  This app could only make half of the camera live image visible in the app dashboard

Known Limitations

• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.
• RTSP-Streaming
  If only one image sensor module is connected in the M73, the streaming mode  Raw cannot be selected at this time.

top

Software Release MX-V7.0.5.16 − for M7 Camera Model M73

Creation Date: 2020-06-30

Publishing Date: 2020-07-02

Enhancements and Improvements

Support for thermal sensor modules

This version supports the new M73 thermal sensor modules. These are available with different lenses (focal lengths), with and without thermal radiometry function and in contrast to the Mx6 camera line also in VGA resolution. The thermal sensor modules are permanently installed in an M73 front panel, which is then mounted in the M73 camera. A thermal sensor module can be combined with an image sensor module and another function module (e.g. an IR light module). The setup and use of thermal (TR) events is done exactly as in Mx6 cameras with thermal sensor modules.

Bugfixes

• Intensity IR Light Module
  The setting of the IR Light Power Level in the Admin  > Hardware Configuration > Assign Wires dialog was ineffective when activating the IR Light module by a day-night switch. The module has always been activated with the highest intensity.
  

Known Limitations

• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.
• RTSP-Streaming
  If only one image sensor module is connected in the M73, the streaming mode  Raw cannot be selected at this time.

top

Software Release MX-V7.0.4.18-r1 − for M7 Camera Model M73

Creation Date: 2020-05-12

Publishing Date: 2020-05-13

Enhancements and Improvements

WDR Feature

The behavior of the Wide Dynamic Range feature that aims at improving images with large differences in image illumination has been improved substantially compared to the predecessor release. In particular, you do not need to define an exposure window to improve the results. In addition, this feature has been improved if an IR Light module is attached. If the camera activates this module due to diminishing illumination, overexposure of objects close to the camera is reduced. The WDR function can be activated in the Setup Menu > Image Control > Exposure Settings dialog, and three modes are available to adapt to the current scene:  Low for low, Medium for medium, and High  for large brightness differences between dark and bright areas in the image.

ONVIF-T and H.265

With this software version, the M7 camera models support the ONVIF-T standard. This includes in particular the use of  H.265  as a video codec and the display of texts into the live image using the ONVIF-T function OSD (OnScreenDisplay).

In addition, the H.265 codec can also be used independently of the integration of an M7 camera via ONVIF-T for RTSP streaming by any RTSP client, such as VLC. H.265 can also be used as a video codec when integrating M7 models into the Genetec Security Center via the Genetec integration interface.

USB Interface

With this version, the USB interface of the camera can be used for the following functions:

• Storage of video and audio data in MxFFS format on USB storage media (USB sticks, SSD drives or hard drives). The camera supports the USB 2.0 standard.
• Integration of an MX-232-IO box for the use of its signal inputs/outputs and/or its serial interface
• Connecting a USB FTDI adapter for standard RS232 connections

Other Improvements

• Improved data rate for MxPEG/M-JPEG codec
  The video codecs MxPEG and M-JPEG have been further optimized, so that data rate savings of about 15% are achieved with the same image quality, depending on the setting.
• Saving the current live image
  The Save Image function in the live view of the web browser has been improved. Now, regardless of the live stream, an image with the best possible JPEG quality is saved.

Notes

• The two lines at the bottom of the live image, which contain event information, are no longer output in the saved image with this function.
• If necessary, the function's behavior can be configured to restore the old behavior. For this purpose, the parameter  SAVE_IMAGE_BUTTON=live can be added to the camera configuration file in the SECTION homepage.  Currently, this value is implicitly set to best.

Bugfixes

• IR Light Module disabled (V7.0.4.18-r1)
  In version 7.0.4.18, when switching to the night mode, a possible existing IR Light module was no longer activated.
  
• Message events of the Facial Recognition App
  When using the Visage Technology Face Recognition app in Operation Mode  Recognition, message events named  VT_Face were triggered even if a person, who had not previously been trained in Operation Mode Enrollment , was detected by the system. The event had to be restricted to already known people by additional filtering of the event content. This is no longer necessary, as in Operation Mode Recognition events are only triggered when previously learned faces are detected.
• Lens configuration
  In the Admin -> Hardware Configuration area, the Lens Configuration dialog could be opened incorrectly and the settings made there were ineffective. The dialog has been removed.
  

Known Limitations

• Dialog Integration Protocols
  For M73 cameras with only one sensor module, the Admin -> Camera Administration -> Integration Protocols dialog is empty after activating one of the protocols ONVIF or Genetec via the installation wizard of the web browser. This state can be corrected by first deactivating the set protocol ONVIF or Genetec and then turning it back on.
• RTSP-Streaming
  If only one image sensor module is connected in the M73, the streaming mode  Raw cannot be selected at this time.

top

Software Release MX-V7.0.1.20 − for M7 Camera Model M73

Creation Date: 2020-02-13

Publishing Date: 2020-02-14

The following describes the new features, enhancements and enhancements compared to the first version 7.0.0.111 delivered with M73 cameras.

Enhancements and Improvements

Support for the new IR-Cut Day & Night Sensor Modules and IR Light Modules

IR-Cut Day & Night Sensor Module
The M73 supports the use of the new IR-Cut Day & Night sensor modules. These are color sensor modules with an integrated swivel IR blocking filter for day and night operation. This filter is automatically switched off at low illumination, which also provides bright images at night and using the possibly integrated IR module. This automatic mode is activated by factory setting and the Lux value used to switch to night mode can be set in the setup > image control > general image settings dialog. In the same dialog, the filter can also be switched manually if required.

IR Light Module
The activation of a possible integrated IR Light module is coupled to the activation of the "Night Mode" as follows:

• If an IR-Cut Day & Night sensor module is also used, this is done when switching the IR blocking filter off (see above).
• If the IR Light module is used together with a normal day and night sensor module, the IR Light module is activated when the night sensor module is activated by the automatic day-night switching. 

Apps

Additional App for face recognition
In addition to the A.I. Tech Apps AI* the Visage Technology Face Recognition App for facial recognition is also available with this version. After installation (see the following notes), the activation and configuration of this App is done exactly as for the other Apps in the Setup > Certified App Control > Certified App Settings dialog.

Apps AI* from A.I. Tech
This firmware release also includes updated and improved versions of A.I's AI* Apps. Tech (see below)

Bugfixes

• A.I. Tech App
• If one of the A.I. Tech Apps was configured with a sensor other than the one currently shown in the camera live image, the camera could have done a restart.
• With the application of some A.I. Tech apps (e.g. AIParking) a camera restart could occur after a few minutes.
• In addition, after activating the A.I. Tech apps, there were performance problems with camera operation in the web browser.
• Full screen recording
  When using the full screen recording, there could be image errors (stripes in the picture).

Known Limitations

• RTSP-Streaming
  If only one image sensor module is connected in the M73, the streaming mode  Raw cannot be selected at this time.
• USB interface not supported
  This version doesn't support the hardware USB interface yet.